WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : CK-D2GSXXXLDA  

    CK 2 Series Large Diameter Gas Saver Kit, with Alumina Cup
    CK-D2GSXXXLDA

    Select Option 
    Prices From £65.10 ex VAT

    The CK Large Diameter Gas Saver T front end is used to provide an inert atmosphere for the welding of reactive metals such as titanium, molybdenum, nickel-based and aluminium-based alloys, as well as non-reactive metals like stainless steel. This design is lightweight, allowing for operator comfort and accurate control. The front end also uses a clear Pyrex cup creating excellent visibility of the weld puddle.

    The clear cup features an inside diameter of 1 1/8" (28.57mm) which is the largest cup orifice available on the market today. This design offers a replaceable, interchangeable tungsten adaptor; and a universal collet body, creating less inventory, and allowing inexpensive screen replacement. Tungsten stick-out can be up to 2" (50.8mm) in certain conditions.

    This kit allows welders to weld low amperage Titanium without a trailing shield. Great for tack welding outside of an inert chamber and repairs of small cracks. 2 Series Fits 9 & 20 Torch Models.

    CK Large Diameter Gas Saver Kit

    Product Details

    CK 2 Series Gas Saver Kits FAQs

    Gas lens front-end kits for small TIG torches: what they do, how to choose the cup and how to get the best shielding from them.

    What is a gas saver kit and what does it do on a TIG torch?icon-minus-redicon-plus-red

    A gas saver kit is a gas lens front end. It replaces the standard collet body and cup with a body that holds fine mesh screens, plus a matching cup, collet and usually the insulating parts that go with them. The screens smooth the argon into a steadier, more even column as it leaves the cup, instead of the more turbulent stream a standard collet body tends to produce.

    The smoother flow gives better coverage of the weld pool and the hot tungsten, which helps most on vertical, corner, edge and curved work and on metals that react easily with air, such as stainless steel and titanium.

    Will a gas saver kit really use less gas, and how do I set the flow?icon-minus-redicon-plus-red

    Because the flow leaving the cup is smoother, a gas lens can often shield well at a lower flow than the same size cup on a standard collet body. In one training example a number 8 cup needed about 10 litres per minute with a standard body but about 5 with a gas lens. How much you save depends on the cup size, the job and draughts, so treat headline percentages as best-case figures.

    There is no single exact rule for the setting, so start from the maker's guidance for your cup and torch, then reduce to the lowest flow that still gives clean, bright welds. Too much flow causes turbulence, can pull air in and can make the arc unstable. Flowmeters are not always accurate, so a flow tester is a useful check.

    Should I choose an alumina cup or a glass cup?icon-minus-redicon-plus-red

    Alumina (ceramic) cups are the more durable choice and suit general work and a busy workshop. Glass (borosilicate) cups let you see through to the arc and the joint, which helps in inside corners, inside pipe and around tubing where a solid cup blocks the view.

    The trade-off is that glass is more fragile and breaks more easily if the torch is dropped or knocked. Check the maker's guidance for the current each cup type can handle, and replace any cup that is cracked or chipped. Many welders keep both types and swap depending on the job.

    How do I know which kit fits my torch?icon-minus-redicon-plus-red

    Kits are made for a particular torch series or head style, so start by identifying your torch from the markings on the head, the handbook or the torch maker's parts list. The small-torch (2 series) kits are listed for the 9 and 20 style torches, and makers describe them as fitting most standard silicone-rubber-insulated torch bodies, so check the fit in the product description rather than assuming.

    Then match the tungsten diameter, because the collet and gas lens adapter are sized to the electrode, and choose between standard, large diameter or stubby styles to suit your access and the cup you want. Our team can help you match a kit to your torch details.

    Shop Similar Categories