WE HAVE SOME GREAT LIMITED-TIME OFFERS - CLICK HERE TO VIEW THEM WE SHIP WORLDWIDE    /    All UK ORDERS GREATER THAN £75 EX VAT DELIVERED FREE    /    WE SHIP WORLDWIDE    /    ALL EUROPEAN ORDERS GREATER THAN £500.00 ex VAT DELIVERED FREE    /    WE SHIP WORLDWIDE
    Share this page on Facebook   Share this page on LinkedIn   Share this page on Twitter   Share this page on Whatsapp   

    Rapid Ref : GOV-600-FDHT  

    Gullco High Temperature Flux Holding Oven, 265Kg Capacity. 100-850°f (38-455°c) 11400 Watts, 440v 3ph
    GOV-600-FDHT

    £10534.00  EX VAT
     Buy in 3 easy interest free payments of £3511.33† with
    Please note, this product does not qualify for our standard shipping rates outside of the UK Mainland. Please contact us for shipping rates for this product.

    This fully insulated 265Kg capacity high-temperature Flux Bake Oven is similar in design to the above Model GOV 600 FD3, except incorporates high-temperature insulation, high-temperature wiring and the flux heating system which incorporates 11,400 watts of low-density elements. Temperature range 38-455°c (100°-850°f). An individual thermostat controls each hopper to provide individual temperature control. All for operation on 440volts, 3 phase power supply. Weight 158Kg. Dimensions: 1372mm H x 1065mm W x 610mm D.

    Flux Ovens FAQs

    Answers to common questions about holding ovens and heated hoppers for submerged arc welding flux.

    Why does submerged arc flux have to be kept dry?icon-minus-redicon-plus-red

    Flux that has taken up moisture releases hydrogen into the weld pool when it melts in the arc. Moisture in the flux or electrode coating is the principal source of hydrogen in flux-based welding. Hydrogen in the weld can lead to delayed cracking, especially in higher-strength steels, and damp flux is also a known cause of porosity.

    Keeping flux dry from the packet to the weld is therefore part of controlling weld quality. The flux maker's data sheet and your welding procedure set out how dry it needs to be for the job.

    What is the difference between drying flux and holding flux in an oven?icon-minus-redicon-plus-red

    Drying (sometimes called re-baking) removes moisture that flux has already picked up, and it uses a much higher temperature for a set time. Holding is the lower temperature used to keep dry flux dry until it is needed, which is what a holding oven or heated hopper is for.

    Baking the flux before use may be necessary, and if flux is not used within a short time the hoppers on the equipment should be heated to limit moisture pick-up. Check the flux data sheet for the drying and holding temperatures, because they vary between flux types and makers.

    Do all submerged arc fluxes absorb moisture in the same way?icon-minus-redicon-plus-red

    No. Fused fluxes are made by melting and crushing, and are resistant to moisture pick-up. Agglomerated (bonded) fluxes are made from a baked wet mix with binders that attract moisture, so moisture pick-up can be a problem on the shop floor and baking before use may be needed.

    This is why the type of flux affects how you store and handle it. Check the flux packaging and data sheet for the type and the maker's handling rules, and ask our team if you are unsure which oven arrangement suits your flux.

    Can compressed air used for flux recovery affect the flux?icon-minus-redicon-plus-red

    Yes. Flux recovery units driven by compressed air can carry moisture and oil into the recovered flux if the air is not dry and clean. Compressed air used with a flux recovery unit should be thoroughly dried.

    A damp or oily recirculating flux can cause porosity, even if it was dry in the oven. Drain the air line and filters regularly, and follow the recovery unit maker's instructions. Keep the recycled flux separate from any contaminated or wet flux.

    Shop Similar Categories